DMKR 7.2GHz 60CH 5W 15V-36V 2S-8S 20mm*20mm FPV Analog VTX

Product Appearance

 

 

Product Dimension

 

 

Function Instroduction

 

 

1.Channel indicator: Red LED
2.Band indicator: Blue LED
3.Power indicator: Green LED
4.Band & Channel changer button
5.Power changer button
6.1.0 6P Power connector
1. Channel indicator: Red LED
2. Band indicator: Blue LED
3. Power indicator: Green LED
4. Band & Channel changer button
5. Power changer button
6. 1.0 6P Power connector
7. SMAMother seat inner hole

 

Control Method and LED Indicator

 

1. Button ④ serves as the frequency point and band switch; each short press cycles to the next frequency point, with the corresponding red LED flashing. The sequence is: Frequency Points 1, 2, 3, 4, 5, 6, 7, 8. This operation cycles repeatedly; see the diagram below for details!

 

Short press button ④ to switch channel
Red LED	CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8
	Flash once	Flash twice	Flash for 3 times	Flash for 4 times	Flash for 5 times	Flash for 6 time	Flash for 7 times	Flash for 8 times

 

2. Press and hold button ④ to switch frequency bands. Holding for 5 seconds causes the corresponding blue LED to flash, cycling through frequency groups Aand B. This operation can be repeated; see the diagram below for details!

 

Long press button ④ to switch bands
Blue LED	Band A	Band B	Band E	Band F	Band R	Band P	Band H	Band U
	Flash once	Flash twice	Flash for 3 times	Flash for 4 times	Flash for 5 times	Flash for 6 time	Flash for 7 times	Flash for 8 times

 

3. Button ⑤ is the power adjustment button. Each short press cycles through power levels, alternating between 25mW, 2.5W, and 5W. The green LEDserves as the power indicator, with the following flashing patterns: 25mWflashes once, 2.5W flashes twice, and 5W flashes 3 times. Press and hold for 3 seconds to enter pit mode, where the green light remains steady. See the diagram below for details!

 

Short press button ⑤ Power switch
Green LED	Pit Mode	25mW	2.5W	5W
	Everlasting brightness	Flashes 1 time	Flashes Twice	Flashes 3 times

 

Note: This image transmission device has a temperature protection function. When the temperature of the image transmission device exceeds 100°C, the transmission power of the image transmission device will be reduced by one level. If the temperature remains above 100°C, the transmission power will be reduced by another level until it reaches the lowest power level (25mW). At this point, the temperature of the image transmission device will decrease. When the temperature drops to 95°C, the transmission power will return to the originally set power level.

 

Frequency Table

 

Frequency Table
Channel Band	CH1	CH2	CH3	CH4	CH5	CH6	CH7	CH8
BAND A	6110	6130	6150	6170	6190	6210	6230	6250
BAND B	6270	6290	6310	6330	6350	6370	6390	6410
BAND E	6430	6450	6470	6490	6510	6530	6550	6570
BAND F	6590	6610	6630	6650	6670	6690	6710	6730
BAND R	6750	6770	6790	6810	6830	6850	6870	6890
BAND P	6910	6930	6950	6970	6990	7010	7030	7050
BAND H	7070	7090	7110	7130	7150	7170	7190	7210
BAND U	6115	6265	6425	6585	6745	6905	7065	7185

 

Illustrate of 8P 1.0 Wiring

 

 

Notice for Use

 

1. The VTX must be installed with space to ensure that the air convection around the module to ensure that the module heat dissipation; otherwise, the module overheating protection start, reduce the power to transmit, or even shut down the power to transmit.
2. It is recommended that before turning on the power, to ensure that the correct voltage range, positive and negative poles are correct, so as not to burn components.
3. It is recommended that before turning on the power, make sure that the RF RFoutput has been installed antenna, which can extend the life of the module.
4. Please read the instruction manual before use, so that you can correctly wire and extend the module service life

 

Legal Disclaimer

Important Notice on Radio Frequency Usage

 

1.DMKR high-performance VTX modules (3W-7W) are powerful RF instruments.Designed for specialized industrial, research, and laboratory applications. By purchasing this product, the buyer acknowledges and agrees to the following:

2.Regulatory Compliance: It is the buyer’s sole responsibility to ensure that the operation of this device complies with local laws, radio frequency regulations, and licensing requirements in their respective country or region.

3.Professional Use Only: This equipment should only be operated by qualified professionals. DMKR is not liable for any legal consequences, fines, or damages resulting from illegal or improper use.

4.Frequency Licensing: The 7.2GHz band may be restricted or require a specific technician’s license for operation. Please consult your local telecommunications authority (e.g., FCC, OFCOM, BNetzA) before powering on the device.

5.Risk of Misuse: The user assumes all risks associated with the deployment of this hardware. DMKR does not authorize the use of these devices in prohibited areas, including but not limited to, near airports or restricted government airspace.

6.No Liability: In no event shall DMKR be held liable for any direct, indirect, or incidental damages, including hardware failure of the UAV/UGV or legal intervention, arising out of the use or inability to use this product.

7.Safety Warning: High-power RF devices generate significant heat and radiation. Ensure proper thermal management and maintain a safe distance during operation.

8.Hardware Modification: Unauthorized modification of the firmware or hardware may void compliance certifications and safety protections.